Koninklijke Bibliotheek, National Library of the Netherlands
IP1604914519296
Graphene oxide films for field effect surface passivation of silicon for solar cells
Vaqueiro-Contreras, M.
Bartlam, C.
Bonilla, R.S.
Markevich, V.P.
Halsall, M.P.
Vijayaraghavan, A.
Peaker, A.R.
text
article
monographic
Solar energy materials and solar cells
continuing
09270248
0000000010891
187
C
text
Born digital tijdschriften
KB collectiekavel
text
Elektronische Wetenschappelijke Tijdschriften
EWTIJ
10.1016/j.solmat.2018.08.002
urn:nbn:nl:kb-1604914519040
Automatisch gegenereerd op basis van de EWTIJ XML in release 1.5 van het digitaal magazijn.
SOLMAT
9561
S0927-0248(18)30405-7
10.1016/j.solmat.2018.08.002
The Authors
Fig. 1
Effective lifetime maps of a DSP FZ p-type (> 1000 Ω·cm) silicon sample (a) bare and (b) GO coated, and a SSP Cz p-type (2.8 Ω·cm) silicon sample (c) bare and GO coated.
Fig. 1
Fig. 2
Effective lifetime maps of samples cut from a B-doped Cz wafer of thickness 625 ± 25 µm, passivated with (a) 4 mg/ml GO, (b) I-E solution, and (c) PECVD SiN
x
.
Fig. 2
Fig. 3
Averaged effective lifetime values of samples cut from a B-doped Cz wafer of thickness 200 ± 5 µm. Initial non-passivated value is identified with the circular marker, whereas the diamond marker represents the passivated averaged values with 2 mg/ml GO after air ambient storage.
Fig. 3
Fig. 4
AFM images of sheets from a low (a) and high (b) pH GO dispersion. PeakForce-KPFM maps from the same GO sheets with low (c) and high (d) pH. (e) Transmission IR absorption spectra from silicon samples coated with low and high pH 3 mg/ml GO.
Fig. 4
Fig. 5
Effective lifetime maps of samples cut from a B-doped FZ wafer of thickness 300 ± 5 µm, passivated with 2 mg/ml GO with (a) pH 3.6 (as prepared) and (b) pH 10. The blue boxes highlight the highest lifetime areas.
Fig. 5
Graphene oxide films for field effect surface passivation of silicon for solar cells
M.
Vaqueiro-Contreras
a
⁎
C.
Bartlam
b
R.S.
Bonilla
c
V.P.
Markevich
a
M.P.
Halsall
a
A.
Vijayaraghavan
b
A.R.
Peaker
a
a
School of Electrical and Electronic Engineering, University of Manchester, Manchester M13 9PL, UK
School of Electrical and Electronic Engineering, University of Manchester
Manchester
M13 9PL
UK
b
School of Materials, University of Manchester, Manchester M13 9PL, UK
School of Materials, University of Manchester
Manchester
M13 9PL
UK
c
Department of Materials, University of Oxford, Oxford OX1 3PH, UK
Department of Materials, University of Oxford
Oxford
OX1 3PH
UK
⁎
Corresponding author.
Abstract
In recent years it has been shown that graphene oxide (GO) can be used to passivate silicon surfaces resulting in increased photocurrents in metal-insulator-semiconductor (MIS) tunneling diodes, and in improved efficiencies in Schottky-barrier solar cells with either metal or graphene barriers, however, the source of this passivation is still unclear. The suggested mechanisms responsible for the enhanced device performance include the dangling bond saturation at the surface by the diverse functional groups decorating the GO sheets which reduce the recombination sites, or field effect passivation produced by intrinsic negative surface charge of GO. In this work through a series of measurements of minority carrier lifetime with the microwave photo-conductance decay (µPCD) technique, infrared absorption spectra, and surface potential with Kelvin probe force microscopy (KPFM) we show that there is no evidence of significant chemical passivation coming from the GO films but rather negative field effect passivation. We also discuss the stability of GO's passivation and the flexibility of this material for its application as temporary passivation layer for bulk lifetime measurements, or as a potential cheap alternative to current passivation materials used in solar cell fabrication.
Highlights
•
Intrinsic properties of graphene oxide (GO) make it a suitable material for surface passivation.
•
GO is proven to serve as a potential cheap alternative for silicon surface passivation.
•
Graphene oxide's negative charge is demonstrated to be the source of the passivation.
Keywords
Surface passivation
Graphene oxide
Solar cells
Dielectric charge
1
Introduction
It is well known that one of the most effective approaches to improve the efficiency of silicon-based solar cells, whilst maintaining low cost, is to increase the lifetime of photo-generated carriers by reducing recombination at the surface and in the bulk of low cost materials [1]. Therefore the study of new materials which may suppress surface recombination in such materials is important both because they may promote a minority carrier lifetime improvement in commercial solar cells but also, in the laboratory, they may allow more accurate measurements of silicon's bulk lifetime. For these reasons such new materials remain a topic of widespread interest [2–4].
Generally, for surface passivation materials we need to consider three material property aspects: the characteristics of the material to be passivated (doping type and resistivity); the physical properties of the passivating materials (optical, chemical and electrical), to determine the type of passivation that the material will provide including bond saturation, the field effect control of carriers, refractive index, and stability; and processing requirements like surface cleaning and synthesis methods. With this in mind, in this work we have studied the passivation capabilities of graphene oxide which we know fulfils some key requirements for surface passivation including: high transmittance [5], fixed surface negative charge [6,7] and high refractive index [8,9]. This is all combined with the fact that GO is water dispersible making its deposition and removal extremely simple. Most common GO deposition techniques include: dip coating, spin coating, and spray coating, techniques which can be easily incorporated to a production line. In addition, it has been recently shown that for a GO derivative dispersion with an optimal dilution, it is possible to obtain uniform coverage even on textured silicon surfaces for solar cells [10].
While passivation effects in structures incorporating GO interlayers, such as MOS and graphene/GO/Si devices, have already been reported in literature [11–16], these do not include the study of graphene oxide as a passivation material for solar cells in a scalable to manufacture system. Furthermore, to our knowledge there is no definitive answer as to what is causing the passivation on the surface from the available literature. Thus in this work we aim to answer such a question by providing strong evidence of the influence of the negative surface charge of GO in the passivation of silicon. Additionally, we demonstrate the passivation effect of GO in different silicon materials and the inclusion of GO's passivation capabilities compared to that of the industry standard material, silicon nitride (SiN
x
) used for solar cell passivation [17] and the widespread temporary passivation attained from Iodine-Ethanol (I-E) solution immersion for bulk lifetime measurements [3].
2
Materials and methods
In this work a range of float zone (FZ) and Czochralski (Cz) grown, boron-doped silicon wafers with ‹100› crystal orientation, double (DSP) and single (SSP) side polished, with resistivities between 1 and 1000 Ω·cm, and thicknesses from 200 to 625 µm have been used to study the passivation effect of GO. Most of the measurements were carried out in cut samples of 2 × 2 cm2 which were subjected to the standard cleaning “RCA 1” procedure as described in Ref. [18]. However, the usually applied subsequent HF dip of the samples was not performed since it was found that such step resulted in a diminished passivation of the silicon surface due to the lack of hydrophilicity on the surface provided by either the native oxide or the oxide left by the H2O2. It must be noted as well that the samples were cleaned and left in the desiccator for at least 3 days before the GO deposition, and their lifetime measured before and after the deposition to avoid the inclusion of the RCA 1 passivation effect into consideration, it was determined that this process takes place within that period before stabilisation.
GO was prepared by a modified Hummers method [19] whereby natural flake graphite (30 mesh, 96%C) was oxidised and exfoliated. Sulphuric acid (H2SO4, 98%), hydrogen peroxide (H2O2, 30%), ammonium hydroxide (NH4OH, 35%) (Sigma Aldrich); sodium nitrate and potassium permanganate (KMnO4, Alfa Aesar) were all used as supplied and without any further purification. The oxidised graphite was repeatedly washed and exfoliated using a 3% wt. H2SO4/ 0.5% wt. H2O2 mixture and then washed further with deionised water until a pH of 7 was reached for the supernatant to ensure the removal of the H2SO4. The GO pellet had a pH of 3.6. To adjust the pH of GO, 100 µl of ammonium hydroxide was added to under stir to give a pH of 9.9 ± 0.01 measured with a Mettler Toledo F20 pH meter.
For the silicon nitride deposition we used the Plasma-Enhanced Chemical Vapour Deposition (PECVD) technique for 2 min, to achieve a film thickness of 90 nm ± 3 nm according to spectroscopic ellipsometry. This was done on a PlasmaPro 100 PECVD system from Oxford Instruments with: 20:20 sccm SiH4: NH3 gas flow, 300 mTorr chamber pressure, 400 °C table temperature, 13.56 MHz plasma generated frequency and 50 W of power as deposition parameters.
Kelvin Probe force microscopy on the PeakForce tapping frequency-modulated mode (FM-KPFM) using SCM-PIT-V2 tips was used to map the surface potential of single GO flakes on a Bruker Dimension FastScan. Samples for this measurements were prepared by spin coating 0.5 mg/ml of GO for 60 s at a speed of 1000 rpm and left to dry on a desiccator overnight. Infrared absorption spectroscopy on 200 nm ± 20 nm thick GO coated silicon samples was carried out with a Hyperion 3000 FT-IR microscope with a resolution of 4 cm−1 in transmission mode.
A Semilab WT-2000 PVN was used for minority carrier lifetime mapping by the microwave photoconductivity decay (µPCD) technique, with a 905 nm LASER excitation and a microwave source operating at ~10 GHz. Hence the presented effective lifetime maps show the averaged lifetime down to a few tens of microns into the sample. The level of passivation achieved by GO layers was tested in several samples by the measurement of their effective lifetime (τ
eff
) by µPCD mapping, with the assumption that both sides of each sample were equally passivated. Next, what is considered the upper limit of the surface recombination velocity (S
UL) was calculated by assuming the bulks lifetime (τ
bulk
) to be infinite, thus giving S
UL=W/2(τ
eff
), with W representing the sample thickness.
3
Results and discussion
3.1
GO effect on minority carrier lifetime
We have carried out transient photoconductance mapping to compare the level of surface passivation achieved by GO in various sets of samples, here we present the comparison of GO's passivation on an electronic grade FZ material to that of a solar grade Cz material.
Fig. 1 show the lifetime maps of the FZ and the Cz boron doped samples before (a, c), and after (b, d) GO passivation, respectively. For the FZ sample it can be observed that the τ
eff
approaches 1 ms in some areas. Nevertheless, considering the maximum effective lifetime in the sample to be
τ
max
= 900 µs and W = 500 µm we obtain a S
UL ≈ 27 cm s−1, whereas from the τ
max
= 820 µs and W = 200 µm of the Cz sample the calculation results in a S
UL ≈ 30 cm s−1. These values are comparable to the surface recombination velocities of some existent surface passivation materials [3,4]. Moreover, we have compared the surface passivation of GO to that of PECVD deposited SiN
x
and I-E solution immersion. The passivation was carried out on samples cut from a solar grade SSP Cz p-type wafer (25 ± 7.5 Ω·cm), the lifetime comparison is presented in
Fig. 2. The calculated upper limit surface recombination velocities from each sample are: 363 cm s−1, 322 cm s−1 and 202 cm s−1 for GO (Fig. 2a), I-E (Fig. 2b) and SiN
x
(Fig. 2c), respectively. These results indicate that in some silicon materials it is possible to attain very similar levels of surface passivation with GO coatings to those obtained by the widely used SiN
x
and I-E techniques.
With respect to the surface passivation stability we have found that the GO passivation effect can last for several days, however there appears to be some unpredictable behaviour in GO's passivation after storage. We have observed there is an increase in averaged lifetime after a few days of air ambient storage of the samples, which we suggest to be attributed to the interlayer water molecule release which decreases the spacing between GO sheets and increases the negative charge on the surface. Thus, after reaching an average τ
eff
maxima, the lifetime begins to decrease slowly as shown in
Fig. 3, where effective lifetime degradation is shown for a B-doped (2.8 Ω·cm), SSP, Cz grown silicon sample coated with 2 mg/ml GO after air storage during 70 days. It must be noted that Fig. 3 shows the averaged effective lifetimes of 3 × 3 cm2 samples with some deviations due to GO aggregation sites, thus making it difficult to appreciate the amount of stability obtained within the first two weeks of deposition. The data point with a circular marker in Fig. 3 represents the averaged lifetime of the bare sample which in comparison to the data taken after 1600 h shows that even after the 70 day lifetime degradation there is still some passivation present from the GO coating. We believe that it may be possible to improve the stability with the application of an encapsulation or capping method. This approach would avoid the gradual reduction of dried GO at ambient conditions in the presence of humidity and high pH which is likely to be the cause of the passivation degradation.
3.2
Passivation mechanism
We have demonstrated the capability of GO to passivate silicon surfaces by τ
eff
mapping of silicon samples. This is in line with the observations of higher efficiencies from some authors in literature [11–16], however the mechanism responsible of the passivation is still under debate. On the one hand Yang et al. [14] has suggested the passivation to be due to surface dangling bond saturation provided by the hydroxyl and carbonyl groups which decorate the graphene-like sheet of GO, whereas Hsu et al. [12] and Jiao et al. [13] attribute the passivation to the negative surface charge of GO. Henceforth we provide some evidence to support the latter as the source of the passivation.
It has been largely acknowledged in the literature that the abundant oxygen containing functional groups of GO such as: hydroxyls (C-OH), carboxyls (COOH), and epoxides (C-O-C) are the source of a strong negative surface charge in the GO sheets [7,20,21]. Even though there still exist some dispute on the distribution of these functional groups and their impact on GO's properties, the negative charge attributed to them has been accepted by the 2D material community. GO's negative charge has been observed to be significantly dependent on the pH of GO's colloidal dispersion, and has been measured mostly by the zeta potential technique [16,22–24] and more recently by Kelvin-probe microscopy [25]. In this work we have thus studied the impact of pH on the surface passivation ability of GO in a range of samples, primarily observing the effect of low (3.6 ± 0.01) and high (10 ± 0.01) pH GO solutions in the passivation, this because there were no observable trends from intermediate values as could be expected from the small zeta potential increase in mid values reported in various references [16,22–24].
Firstly, to observe the effect of pH on the surface potential of the GO single flakes (see
Fig. 4
a and b for topography illustration) we used the PeakForce-KPFM technique on both materials. Images of the measurements are shown in Fig. 4
c and d for the low and high pH dispersions, respectively. A cross-section profile of the measured surface potential is also shown in Fig. 4 for both pH's. From these measurements the contact potential difference (VCPD) between the tip and the sample presents a threefold increase in negative potential going from VCPD = 24 ± 7 mV for the low pH GO flake to VCPD = 62 ± 4 mV for the high pH GO flake. These results indicate that there is indeed an increase in negative charges on each GO flake from the basic solution. Moreover an increase in potential with number of GO layers was observed, confirming the results reported by Salomao et al. in [26]. We have carried out FTIR measurements on silicon samples coated with thick layers of the same low and high pH GO dispersions to correlate with functional group content, results are shown in Fig. 4
e. The IR spectra at distinct points of the sample show a rather significant increase in the vibrational frequencies 1042 cm−1 and 1427 cm−1 typically assigned to hydroxyl groups, some increase in the range 1600 − 1750 cm−1, frequencies commonly assigned to carboxyl and hydroxyl groups and a slight decrease in the band 1170 cm−1 assigned to the epoxides [27]. This evidence adds to the argument of having the oxygen-containing groups as the source of negative charge in GO. We then performed photoconductance decay measurements to compare the passivation level attained with each material. In
Fig. 5
a and b we show the compared τ
eff
maps of samples taken from a high resitivity p-type FZ wafer passivated with 2 mg/ml GO solutions with low and high pH, respectively. In these samples the averaged τ
eff
increased from 236 µs in the low pH sample to 389 µs in the high pH sample, suggesting that the added negative charge from the hydroxyl groups improves the passivation. In terms of SUL however, we calculated a value of 17.4 cm s−1 for the low pH sample and 19.5 cm s −1 for the high pH sample, considering the τ
max
measured of 1430 μs and 1282 μs respectively for each sample, these high lifetime areas have been highlighted in Fig. 5. On these areas, an increase of a few tens of nm in GO thickness was measured, indicating that these effect may be the result of a higher aggregation of GO sheets in the low pH solution [22,24] which in turn increases the net negative charge in the area and consequently the field effect passivation. This is in agreement with the negative field effect passivation obtained with GO coating. It must be also noted that, as mentioned in the methods section, the passivation of GO was significantly decreased by the oxide removal from the samples. This fact suggests that there is no dangling bond saturation involved in the passivation mechanism of GO, since a SiO2 thin interlayer (less than 10 nm) has been found to be required for an improved passivation. Such observations contradict the possibility of physical bonding between GO's functional groups and silicon atoms at the surface as suggested by Yang et al. in [14].
4
Conclusions
In this work we have reported the effectiveness of graphene oxide as a surface passivation coating for silicon solar cells. Surface recombination velocities as low as 14.4 cm s−1 have been obtained. Studies on the passivation mechanism attained by GO and its stability are discussed. We found the passivation to be likely explained by the negative fixed charge coming from the oxygen-containing groups, hydroxyl groups in particular, surrounding the GO's flakes and discard previous suggestions of predominant chemical passivation. The simplicity of GO's deposition and removal without surface damage make this process a good alternative for temporary surface passivation for bulk lifetime measurements. Furthermore, with the use of an appropriate encapsulation method or capping layer deposition, results in here presented demonstrate that GO can be a potential cheap and low risk alternative to currently used surface passivation materials for silicon-based solar cells.
Acknowledgments
We would like to thank Engineering and Physical Sciences Research Council, (EPSRC), United Kingdom for funding under contract under the SuperSilicon PV contract (EP/M024911/1). Financial support was also given by Consejo Nacional de Ciencia y Tecnologia, Mexico CONACyT-Mexico. R.S. Bonilla is the recipient of an EPSRC (UK) Postdoctoral Research Fellowship, EP/M022196/1.
References
[1]
M.A.
Green
S.P.
Bremner
Energy conversion approaches and materials for high efficiency photovoltaics
Nat. Mater.
16
2017
23
34
[2]
R.S.
Bonilla
C.
Reichel
M.
Hermle
P.R.
Wilshaw
Extremely low surface recombination in 1 $Ω$ cm n-type monocrystalline silicon
Phys. Status Solidi - Rapid Res. Lett.
11
2017
1600307
[3]
N.E.
Grant
J.D.
Murphy
Temporary surface passivation for characterisation of bulk defects in silicon: a review
Phys. Status Solidi - Rapid Res. Lett.
11
2017
[4]
R.S.
Bonilla
B.
Hoex
P.
Hamer
P.R.
Wilshaw
Dielectric surface passivation for silicon solar cells: a review
Phys. Status Solidi
214
2017
1700293
[5]
H.A.
Becerril
J.
Mao
Z.
Liu
R.M.
Stoltenberg
Z.
Bao
Y.
Chen
Evaluation of solution-processed reduced graphene oxide films as transparent conductors
ACS Nano.
2
2008
463
470
[6]
A.
Lerf
H.
He
M.
Forster
J.
Klinowski
Structure of graphite oxide revisited
J. Phys. Chem. B.
102
1998
4477
4482
[7]
D.
Chen
H.
Feng
J.
Li
Graphene oxide: preparation, functionalization, and electrochemical applications
Chem. Rev.
112
2012
6027
6053
[8]
I.
Jung
M.
Vaupel
M.
Pelton
R.
Piner
D.A.
Dikin
S.
Stankovich
J.
An
R.S.
Ruoff
Characterization of thermally reduced graphene oxide by imaging ellipsometry
J. Phys. Chem. C.
112
2008
8499
8506
[9]
L.-C.
Chen
C.-T.
Yu
Y.-C.
Peng
J.-J.
Hung
H.-M.
Chang
S.-D.
Tzeng
C.-M.
Wang
C.-C.
Lin
C.-H.
Lin
Antireflection with graphene oxide
Opt. Mater. Express
6
2016
8
[10]
A.
Nandi
S.
Majumdar
S.K.
Datta
H.
Saha
S.M.
Hossain
Optical and electrical effects of thin reduced graphene oxide layers on textured wafer-based c-Si solar cells for enhanced performance
J. Mater. Chem. C
5
2016
1920
1934
[11]
C.H.
Lin
W.T.
Yeh
M.H.
Chen
Metal-insulator-semiconductor photodetectors with different coverage ratios of graphene oxide
IEEE J. Sel. Top. Quantum Electron.
20
2014
[12]
W.-T.
Hsu
Z.-S.
Tsai
L.-C.
Chen
G.-Y.
Chen
C.-C.
Lin
M.-H.
Chen
J.-M.
Song
C.-H.
Lin
Passivation ability of graphene oxide demonstrated by two-different-metal solar cells
Nanoscale Res. Lett.
9
2014
1
5
[13]
K.
Jiao
X.
Wang
Y.
Wang
Y.
Chen
Graphene oxide as an effective interfacial layer for enhanced graphene/silicon solar cell performance
J. Mater. Chem. C
2
2014
7715
[14]
L.
Yang
X.
Yu
M.
Xu
H.
Chen
D.
Yang
Interface engineering for efficient and stable chemical-doping-free graphene-on-silicon solar cells by introducing a graphene oxide interlayer
J. Mater. Chem. A
2
2014
16877
16883
10.1039/C4TA02216E
[15]
L.
Lancellotti
L.
Sansone
E.
Bobeico
E.
Lago
M.
Della Noce
P.
Delli Veneri
A.
Borriello
M.
Casalino
G.
Coppola, M
I.M.
Giordano
Graphene oxide as an interfacial layer in silicon based schottky barrier solar cells
IET Conf. Publ.
2015
2015
1
4
[16]
V.
Georgakilas
J.N.
Tiwari
K.C.
Kemp
J.A.
Perman
A.B.
Bourlinos
K.S.
Kim
R.
Zboril
Noncovalent Funct. Graph. Graph. Oxide Energy Mater., Biosensing, Catal., Biomed. Appl.
2016
[17]
A.
Aberle
Overview on SiN surface passivation of crystalline silicon solar cells
Sol. Energy Mater. Sol. Cells
65
2001
239
248
[18]
W.
Kern
J.E.
Soc
The evolution of silicon wafer cleaning technology
J. Electrochem. Soc.
137
1990
1887
1892
[19]
J.P.
Rourke
P.A.
Pandey
J.J.
Moore
M.
Bates
I.A.
Kinloch
R.J.
Young
N.R.
Wilson
The real graphene oxide revealed: stripping the oxidative debris from the graphene-like sheets
Angew. Chem. - Int. Ed.
50
2011
3173
3177
[20]
M.
Li
C.
Liu
Y.
Xie
H.
Cao
H.
Zhao
Y.
Zhang
The evolution of surface charge on graphene oxide during the reduction and its application in electroanalysis
Carbon N. Y
66
2014
302
311
[21]
M.M.
Gudarzi
Colloidal stability of graphene oxide: aggregation in Two Dimensions
Langmuir
32
2016
5058
5068
[22]
C.J.
Shih
S.
Lin
R.
Sharma
M.S.
Strano
D.
Blankschtein
Understanding the pH-dependent behavior of graphene oxide aqueous solutions: a comparative experimental and molecular dynamics simulation study
Langmuir
28
2012
235
241
[23]
D.
Li
M.B.
Mueller
S.
Gilje
R.B.
Kaner
G.G.
Wallace
Processable aqueous dispersions of graphene nanosheets
Nat. Nanotechnol.
3
2008
101
105
[24]
S. a.
Hasan
J.L.
Rigueur
R.R.
Harl
A.J.
Krejci
I.
Gonzalo-Juan
B.R.
Rogers
J.H.
Dickerson
SI-Transferable graphene oxide films with tunable microstructures
ACS Nano.
4
2010
7367
7372
[25]
M. Jaafar, Step like surface potential on few layered graphene oxide Step like surface potential on few layered graphene oxide, Appl Phys Lett. 101, 2012, 263109.
[26]
F.C.
Salomão
E.M.
Lanzoni
C.A.
Costa
C.
Deneke
E.B.
Barros
Determination of high-frequency dielectric constant and surface potential of graphene oxide and influence of humidity by kelvin probe force microscopy
Langmuir
31
2015
11339
11343
[27]
M.
Acik
G.
Lee
C.
Mattevi
A.
Pirkle
R.M.
Wallace
M.
Chhowalla
K.
Cho
Y.
Chabal
The role of oxygen during thermal reduction of graphene oxide studied by infrared absorption spectroscopy
J. Phys. Chem. C.
115
2011
19761
19781
SOLMAT
9561
S0927-0248(18)30405-7
10.1016/j.solmat.2018.08.002
The Authors
Graphene oxide films for field effect surface passivation of silicon for solar cells
M.
Vaqueiro-Contreras
a
⁎
C.
Bartlam
b
R.S.
Bonilla
c
V.P.
Markevich
a
M.P.
Halsall
a
A.
Vijayaraghavan
b
A.R.
Peaker
a
a
School of Electrical and Electronic Engineering, University of Manchester, Manchester M13 9PL, UK
School of Electrical and Electronic Engineering, University of Manchester
Manchester
M13 9PL
UK
b
School of Materials, University of Manchester, Manchester M13 9PL, UK
School of Materials, University of Manchester
Manchester
M13 9PL
UK
c
Department of Materials, University of Oxford, Oxford OX1 3PH, UK
Department of Materials, University of Oxford
Oxford
OX1 3PH
UK
⁎
Corresponding author.
Abstract
In recent years it has been shown that graphene oxide (GO) can be used to passivate silicon surfaces resulting in increased photocurrents in metal-insulator-semiconductor (MIS) tunneling diodes, and in improved efficiencies in Schottky-barrier solar cells with either metal or graphene barriers, however, the source of this passivation is still unclear. The suggested mechanisms responsible for the enhanced device performance include the dangling bond saturation at the surface by the diverse functional groups decorating the GO sheets which reduce the recombination sites, or field effect passivation produced by intrinsic negative surface charge of GO. In this work through a series of measurements of minority carrier lifetime with the microwave photo-conductance decay (µPCD) technique, infrared absorption spectra, and surface potential with Kelvin probe force microscopy (KPFM) we show that there is no evidence of significant chemical passivation coming from the GO films but rather negative field effect passivation. We also discuss the stability of GO's passivation and the flexibility of this material for its application as temporary passivation layer for bulk lifetime measurements, or as a potential cheap alternative to current passivation materials used in solar cell fabrication.
Highlights
•
Intrinsic properties of graphene oxide (GO) make it a suitable material for surface passivation.
•
GO is proven to serve as a potential cheap alternative for silicon surface passivation.
•
Graphene oxide's negative charge is demonstrated to be the source of the passivation.
Keywords
Surface passivation
Graphene oxide
Solar cells
Dielectric charge
KBJ00000000013892
2020-11-05T18:42:19
S300.6
S300
S0927-0248(18)30405-7
10.1016/j.solmat.2018.08.002
SOLMAT
0927-0248
9561
FLA
NON-CRC
UNLIMITED
EPSRC
2018-08-10T04:35:57Z
09270248/v187sC/S0927024818304057/main.xml
58841
MAIN
JA 5.5.0 ARTICLE
FULL-TEXT
09270248/v187sC/S0927024818304057/main.assets/gr1.jpg
60210
IMAGE-DOWNSAMPLED
09270248/v187sC/S0927024818304057/main.assets/gr2.jpg
25722
IMAGE-DOWNSAMPLED
09270248/v187sC/S0927024818304057/main.assets/gr3.jpg
16106
IMAGE-DOWNSAMPLED
09270248/v187sC/S0927024818304057/main.assets/gr4.jpg
61903
IMAGE-DOWNSAMPLED
09270248/v187sC/S0927024818304057/main.assets/gr5.jpg
33526
IMAGE-DOWNSAMPLED
09270248/v187sC/S0927024818304057/main.assets/gr1.sml
14218
IMAGE-THUMBNAIL
09270248/v187sC/S0927024818304057/main.assets/gr2.sml
15915
IMAGE-THUMBNAIL
09270248/v187sC/S0927024818304057/main.assets/gr3.sml
5491
IMAGE-THUMBNAIL
09270248/v187sC/S0927024818304057/main.assets/gr4.sml
8425
IMAGE-THUMBNAIL
09270248/v187sC/S0927024818304057/main.assets/gr5.sml
18291
IMAGE-THUMBNAIL
09270248/v187sC/S0927024818304057/main.pdf
1095170
MAIN
1.7 6.5
DISTILLED OPTIMIZED BOOKMARKED
09270248/v187sC/S0927024818304057/main.raw
24772
S0927-0248(18)X0012-9
SOLMAT
0927-0248
187
C
20181201
1
282
S0927-0248(18)30405-7
10.1016/j.solmat.2018.08.002
189
193
main.pdf
PDF
1.7
local
1604914519040
collectiebehoudsniveau 1
2020-11-09T09:53:20.092+01:00
local
1604914519552
0
SHA-512
ba13b2f35c5b576dfa512f5b6399581ebfd859b2a6969874761f3b4277ec80bd54500394d30fb866201cc19a4e97a7a7c419c33b91ea73dfb6f24e57c63e7a6d
java.security.MessageDigest
1095170
Adobe Acrobat Document
1.7
DIAS
62
DIAS tentative identification
main.pdf
local
1604914519553
0
SHA-512
fa7a0aac0253c07076cb599d587db60114c83d2395ae7488b46c76c88b291181a6b983672e5060785ee2b4c59169085d3ac278a30f4d9fe9395a2d99e7fc2be9
java.security.MessageDigest
24772
not checked
main.raw
local
1604914519554
0
SHA-512
ac6aad80dba51640cf1d64c0fb5dbf130727d846a9b1aa3773e448e4d2e109da21ed18bd53b17272365189c54634d9f185d4f78694f6a8a99e227a984c19dbf7
java.security.MessageDigest
58841
not checked
main.xml
local
1604914519555
0
SHA-512
fc9f82926b491ab8dda01e14591ddb70cc542aacd16392cc263e8543e124cf9fb5fd2ccfd314117604686ceede1eed10bec9346d2e122ec1af1c3be81c361d6d
java.security.MessageDigest
60210
not checked
gr1.jpg
local
1604914519556
0
SHA-512
0a5058919a919e6188c4c87a32bcf11f3994ab7310c14a6e7c350949d0248424ab847f7c0892865ab3c71bebb1959b1228d19c5caa767205b60909a434859826
java.security.MessageDigest
14218
not checked
gr1.sml
local
1604914519557
0
SHA-512
3adc88bb4cf85f625c40b8553b0fa1a7850f2c7aa54a9534ff886ec346082ac08b0693d2ec67c64fab682e9d18680ad757f15ed88654c0998c37aa7cd5fdb93c
java.security.MessageDigest
25722
not checked
gr2.jpg
local
1604914519558
0
SHA-512
68fbd9587e6570a88132dd8d37d3927914d2a264b038e1c6700e0b025598c490626b1052592040c916590f819cc8c9f56b45ac805f4f78e48558a65a259e3e28
java.security.MessageDigest
15915
not checked
gr2.sml
local
1604914519559
0
SHA-512
4cbf763216b209053d821f7901732fcf3d5ea9adcc1690144a06c42e66df550b4217864d1be1620350eb260f70505b5162619df8811c007a2630f099a483d9e1
java.security.MessageDigest
16106
not checked
gr3.jpg
local
1604914519560
0
SHA-512
af9a971980c21dd11da417b2efdcc5645b774dc7fcf755b77088e302f098c9d9f1d47834c1d7533bbc950498fac57f42a1f5b16b47a8bda95f2f6912d1e91c23
java.security.MessageDigest
5491
not checked
gr3.sml
local
1604914519561
0
SHA-512
1067f893e3a91f00080d82b6f0ee6406d13b526476351fe1bb29c38a3c1ed0b74fce911734c334439477f7efa29ef1a584850a5f4239f0a1859d2b6954266972
java.security.MessageDigest
61903
not checked
gr4.jpg
local
1604914519562
0
SHA-512
84507972a1a5177fc2147734c9198d2e3b7ed7070b4b2e6046d29057403c0ff6a153b326611251e606b628ce02a809df3944240b93a2bf96dfe1b7953ce57022
java.security.MessageDigest
8425
not checked
gr4.sml
local
1604914519563
0
SHA-512
28945662c0136791f004565d7262a588035301f5f5dd13fc9ed6eeb70ed11c9ac757da65b505bc007f3ea3dd8d7c24d67234837dfbf9c0c76300818007c32e8e
java.security.MessageDigest
33526
not checked
gr5.jpg
local
1604914519564
0
SHA-512
29da839c49f60aef5489077ceddae683cd13faed4b56d8bcaba542cba81c232603a38fe0fdd1d10a7fdb469130226f8ca9652396ba2a7a1acd9d820e41cabd50
java.security.MessageDigest
18291
not checked
gr5.sml
local
1604914519565
0
SHA-512
deefc6de3d4a732fbe3a17dc214bd0dac75e6bc076fa6511d011ad273806917162da03f49f68f5d274933a1b03c61580d244ef39d2ec857b604d9cba8a5fbe9f
java.security.MessageDigest
14305
not checked
metadata.xml
free
00001
The Authors
KB-agent-id
1
supplier
KB-owner-id
00001
KB-agent-id
1
Elsevier
organization
The Authors
ingestion
2020-11-09T09:53:20.092+01:00
Connector
software
Digitaal Magazijn release 1.5
ejournals_esp_1
streamprofile
ingestion2020-11-10T17:38:09.625+01:00Generic IngestsoftwareDigitaal Magazijn release 1.5